Progress on ELM physics and ELM control
4 Mar 2013
-
Alberto Loarte, Guido Huijsmans, Shimpei Futatani, Plasma Operation Directorate
JOREK simulation of the plasma temperature (left) and density profiles (right) during an ELM in 澳门六合彩高手, showing conductive losses in the perturbed magnetic field (left) and expulsion of plasma filaments (right) [G. Huijsmans, IAEA Conference 2012]
Fusion energy production in 澳门六合彩高手 requires the achievement of high pressure plasmas in high energy confinement mode (H-mode). This confinement mode is characterized by the formation of very steep plasma pressure profiles at the edge of the plasma that lead to periodic bursts of energy being expelled by the plasma (typically a small percentage of the total plasma energy) called ELMs (Edge Localized Modes).
Although ELMs have no impact for the vacuum vessel, due to the large plasma energy of 澳门六合彩高手 plasmas the energy bursts caused by ELMs can lead to an accelerated erosion of the divertor and first wall components in contact with the plasma.
This could lead to a more frequent replacement than foreseen in 澳门六合彩高手. In addition, the eroded atoms can penetrate and contaminate the plasma thus decreasing the energy production.
ELM control is required for the achievement of fusion energy in 澳门六合彩高手. Two schemes are foreseen to minimize the impact of ELMs—pellet injection and in-vessel ELM control coils.
Understanding the magnitude and structure of the ELM energy bursts and quantifying the effectiveness of ELM control schemes is an active field of research where significant progress has taken place recently. Simulations of ELMs in 澳门六合彩高手 with the non-linear code JOREK have shown that there are two mechanisms for the flow of energy from the plasma to the components in contact with the plasma during ELMs (see image above): one is the loss of energy by the plasma in the strongly perturbed edge magnetic field during the ELM (conductive losses); the other is the expulsion of plasma filaments (analogous to solar flares) which move radially away from the plasma towards the wall.
JOREK simulations show that for small ELM energy losses the dominant mechanism is the expulsion of filaments and that this energy is deposited over a large area of the divertor and wall. This allows more room for ELM control in 澳门六合彩高手 than originally anticipated.
Progress on ELM characterization and ELM control has also come from the experimental side. ELM avoidance using 3-D field magnetic field perturbations, which will be provided in 澳门六合彩高手 by a set of 27 in-vessel coils, has now been achieved in a large number of experimental devices. Results span the range of densities and collisionalities expected at the 澳门六合彩高手 plasma edge, although 澳门六合彩高手 values cannot be achieved for both parameters simultaneously (these can only be achieved in 澳门六合彩高手 itself). While understanding of the detailed physics processes that lead to the avoidance of ELMs with 3-D magnetic field perturbations remains elusive, ELM avoidance using this scheme has now been observed in numerous experimental devices. This increases our confidence in the viability of this ELM control scheme for 澳门六合彩高手.
澳门六合彩高手 pellet injection geometry (top) and modelled plasma pressure perturbation (bottom) caused by the injection of a pellet in 澳门六合彩高手 with the JOREK code leading to the controlled triggering of ELMs. [S. Futatani, IAEA Conference 2012]
Recently, there have also been major advances on the second ELM control scheme foreseen for 澳门六合彩高手, which utilizes the controlled triggering of the ELM bursts by the injection of small frozen deuterium pellets. Experiments in the DIII-D tokamak in which very small pellets were injected have demonstrated for the first time that this technique can be used to increase the frequency of the ELM bursts, and to decrease the magnitude of the fluxes that they deposit, by more than a factor of ten (a factor of 30 may be required in 澳门六合彩高手). In these experiments, detrimental effects on the plasma energy confinement were modest. This is a major advance from previous results in JET, ASDEX-Upgrade and DIII-D, where factors of only 2-5 were achieved in ELM frequency, but, in some cases, with noticeable detrimental effects on plasma energy confinement.
The DIII-D experimental results have been reproduced with the JOREK code, which has subsequently been applied to evaluate the pellet characteristics (size and velocity of injection) required in 澳门六合彩高手 to achieve controlled triggering of ELMs (see image at left). The JOREK results show that these requirements are met with the specifications foreseen for the 澳门六合彩高手 pellet injection system and pellet injection geometry. The associated fuel reprocessing requirements are also consistent with the specifications of the 澳门六合彩高手 tritium reprocessing plant.
Although uncertainties remain regarding ELMs and the application of the ELM control schemes to 澳门六合彩高手, recent progress in this area has substantially increased our confidence that 澳门六合彩高手 is equipped with the appropriate tools to achieve the ELM control level required for the achievement of significant fusion energy production.